Skip to content

Edge Crush Test (ECT) Calculator and Chart

Find out how much weight a corrugated box can stack, or which ECT rating your boxes need. It uses the industry’s McKee formula, then takes off what storage time, humidity and stacking really cost — in plain numbers.

Units
1Shipping box, outside size

Not sure of the size? Work it out with the box size calculator first.

2Board
3Load
Boxes in a stack

Product plus box. The stack counts the bottom box; it starts at what fits under a 60 in pallet load.

4Warehouse conditions

Box compression strength (BCT)

–

–
–
–
–
–
–

Your stack

Where the strength goes

Lab strength, then each real-world loss in turn. What is left is the load the bottom box can safely carry.

Every way to build it

The lowest standard grade that holds your stack for each flute, after the certificate weight and size limits.

Board ECT needed Grade to order Lab strength

Box maker’s certificate check

The limits printed on the round stamp on a corrugated box (Rule 41 / NMFC Item 222).

    What is the edge crush test (ECT)?

    The edge crush test measures how much weight corrugated board can take on its edge before it crushes. A small strip is stood upright, flutes running up and down, and squeezed between two plates until it gives way.

    The result is written in pounds per inch of edge. A 32 ECT board holds 32 lb on every inch. Because the walls of a box carry the stack in exactly this way, ECT is the best single number for how well a box will stack — which is why it is printed on the stamp on the bottom of most shipping boxes.

    • Standard test: TAPPI T 811, after conditioning at 73 °F and 50% relative humidity.
    • Higher ECT = stronger walls = a taller, heavier stack.
    • It rates the board, not the box. Box size and storage decide the final strength.
    Edge crush test: a strip of corrugated board stood on edge between two plates being pressed together
    A strip of board on edge, flutes vertical, pressed until it crushes.

    How to use the ECT calculator

    1. 1

      Choose your question

      “How strong is my box?” if you know the ECT, or “Which ECT do I need?” if you know the load.

    2. 2

      Enter the box

      Outside length, width and depth, the board (for strength), and what one packed box weighs.

    3. 3

      Describe the warehouse

      How long boxes sit, how humid it is and how they are stacked. Each choice shows what it costs in strength.

    4. 4

      Read the verdict

      Safe or not, how high you can stack, and the grade to order — then send it to us for a quote.

    ECT chart: grades, Mullen equivalents and weight limits

    Every standard grade, with its burst-test (Mullen) equivalent and the limits printed on the box maker’s certificate under Rule 41 and NMFC Item 222. The highlighted row is the grade in your calculation.

    ECT kN/m Mullen equivalent Max box + contents Max L + W + D Typical use Calculate
    Single wall
    23 ECT 4.0 125# 20 lb (9 kg) 40 in (102 cm) Very light items, inner cartons
    26 ECT 4.6 150# 35 lb (16 kg) 50 in (127 cm) Light retail goods, short trips
    29 ECT 5.1 175# 50 lb (23 kg) 60 in (152 cm) Apparel, light e-commerce
    32 ECT Popular 5.6 200# 65 lb (29 kg) 75 in (191 cm) The standard shipping box: most e-commerce and retail
    40 ECT 7.0 250# 80 lb (36 kg) 85 in (216 cm) Heavier products, taller pallet stacks
    44 ECT Popular 7.7 275# 95 lb (43 kg) 95 in (241 cm) Heavy single-wall boxes, humid or long storage
    55 ECT 9.6 350# 120 lb (54 kg) 105 in (267 cm) Strongest single wall: hardware, liquids
    Double wall
    42 ECT 7.4 200# 80 lb (36 kg) 85 in (216 cm) Entry double wall: extra puncture protection
    48 ECT Popular 8.4 275# 100 lb (45 kg) 95 in (241 cm) Heavy goods, moving boxes, long storage
    51 ECT 8.9 350# 120 lb (54 kg) 105 in (267 cm) Machinery parts, bulk food, export
    61 ECT 10.7 400# 140 lb (64 kg) 110 in (279 cm) Industrial loads, high stacks
    71 ECT 12.4 500# 160 lb (73 kg) 115 in (292 cm) Very heavy or dense products
    82 ECT 14.4 600# 180 lb (82 kg) 120 in (305 cm) Strongest double wall
    Triple wall
    67 ECT 11.7 700# 240 lb (109 kg) 110 in (279 cm) Bulk bins, replaces light crates
    80 ECT 14.0 900# 260 lb (118 kg) 115 in (292 cm) Engines, appliances, export freight
    90 ECT 15.8 1100# 280 lb (127 kg) 120 in (305 cm) Heavy industrial freight
    112 ECT 19.6 1300# 300 lb (136 kg) 125 in (318 cm) Strongest triple wall

    ECT and Mullen grades on the same row are equivalents for carrier rules, not identical boards. The weight is the box and its contents together; the size is the outside length + width + depth.

    Which ECT do I need? A quick guide

    A starting point before you run the numbers.

    32 ECT

    Single wall

    The everyday shipping box. Up to 65 lb gross on the certificate, and plenty for most e-commerce parcels stacked a few high.

    44 ECT

    Single wall

    When boxes are heavier, stacked higher on a pallet, or stored in a humid warehouse — about 38% stronger than 32 ECT.

    48 ECT

    Double wall

    Heavy, dense or valuable products and long storage. Two walls also resist punctures far better.

    61 ECT +

    Double or triple wall

    Industrial parts, bulk loads and export freight that is stacked high for weeks.

    ECT vs Mullen (burst test)

    Two ways of rating corrugated board. Both appear on box stamps; they answer different questions.

    Point Edge Crush Test (ECT) Mullen burst test
    What it measures How much weight the board takes on its edge before it crushes — stacking strength. How much pressure punches through the face of the board — puncture and burst resistance.
    Test TAPPI T 811: a short strip stood on edge and squeezed. TAPPI T 810: a rubber diaphragm pushes until the board bursts.
    Unit Pounds per inch of edge (lb/in), or kN/m Pounds per square inch (psi), written as 200#
    Best for Boxes that are palletised, stacked and stored — most shipping today Boxes handled one by one, rough handling, sharp or dense contents
    On the box stamp “Edge Crush Test 32 lb per inch” “Bursting Test 200 lb per sq inch”

    From ECT to box strength: the McKee formula

    ECT rates the board. To know what a whole box can carry — its box compression strength, or BCT — packaging engineers use the formula McKee, Gander and Wachuta published in 1963.

    BCT = 5.87 × ECT × √(thickness × perimeter)

    • ECT in lb/in; board thickness (caliper) and box perimeter, 2 × (length + width), in inches; BCT comes out in pounds.
    • Box depth hardly matters — it is the length of wall around the box that carries the load.
    • Most accurate for regular slotted cartons whose depth is at least a seventh of the perimeter.

    Worked example

    A 12 × 10 × 8 in box in 32 ECT B-flute (1/8 in thick).

    Perimeter = 2 × (12 + 10) = 44 in

    BCT = 5.87 × 32 × √(0.125 × 44) = 5.87 × 32 × 2.35 ≈ 440 lb

    Stored up to 10 days (−37%) in straight columns (−5%): 440 × 0.63 × 0.95 ≈ 264 lb safe load.

    At 15 lb a box, that is 17 boxes on top of the bottom one: 18 high.

    Why a box is weaker in the warehouse than in the lab

    Lab tests take minutes in perfect conditions. These are the losses the calculator applies; they multiply together.

    Factor Condition Strength lost Why
    Time in storage 10 days / 30 / 90 / 180 days −37% / −40% / −45% / −50% Board creeps under a constant load, so it gets weaker the longer it carries it.
    Humidity 60% / 70% / 80% / 90% RH −10% / −20% / −32% / −52% Paper soaks up moisture from the air. ECT is tested at 50% RH.
    Stacking pattern Aligned / misaligned / interlocked −5% / −12% / −50% Corners carry most of the load. A brick pattern puts them over the weak middle of the box below.
    Pallet overhang Box edges past the pallet −30% The unsupported walls fold instead of carrying weight.
    Pallet deck gaps Wide gaps between boards −15% Bottom boxes sag into the gaps.
    Handling Rough or repeated moves −25% Every knock and corner drop damages the flutes.

    Published industry averages, using the middle of each range. Real boards vary; for critical loads, have a sample compression-tested (TAPPI T 804).

    Corrugated flute guide

    The flute is the wavy middle layer. Taller flutes make thicker board, and thicker board makes a stronger box at the same ECT.

    Flute Thickness Flutes per foot Character Best for
    F 1/32 in (0.8 mm) 128 Very fine, smooth print surface Small retail and cosmetic boxes
    E 1/16 in (1.6 mm) 90 Thin, crisp folds, good print Mailer and subscription boxes
    B 1/8 in (3.2 mm) 47 Good puncture resistance, flat surface Shipping boxes, cans and bottles, displays
    C 5/32 in (4 mm) 39 Best stacking strength of the single flutes The most common shipping carton
    A 3/16 in (4.8 mm) 33 Tallest flute, most cushioning Fragile goods (rare today)
    BC 1/4 in (6.4 mm) — Double wall: B and C combined Heavy goods, moving boxes, export

    Six ways to get more strength from the same box

    Before you pay for a heavier board, check how the boxes are packed and stored.

    • Stack boxes in straight columns, corner on corner. An interlocked pattern can halve the strength.
    • Keep boxes inside the pallet edge: overhang costs about a third of their strength.
    • Let the product help. A box filled to the top, with no headspace, is supported by its contents.
    • Store away from damp floors and walls; a cold store at 90% RH halves a box’s strength.
    • Avoid hand holes and vents in the side walls of boxes at the bottom of a stack — each one weakens the wall.
    • Check the box stamp: it shows the ECT or burst rating and the maximum gross weight.

    Need boxes that stack?

    Custom printed corrugated boxes in the grade your load needs, with no minimum order and free design support.

    Box size calculator
    Custom packaging boxes

    Frequently asked questions

    Everything you need to know before you order.

    What does 32 ECT mean?

    It means a strip of the board, stood on its edge, holds 32 pounds per inch of edge before it crushes (about 5.6 kN/m). It is the most common rating for single-wall shipping boxes, and its certificate allows up to 65 lb of box and contents.

    How much weight can a 32 ECT box hold?

    It depends on the box size and how it is stored. A 12 × 10 × 8 in B-flute box at 32 ECT tests at about 440 lb of top load in the lab. After 10 days of storage and normal stacking, that is about 260 lb it can safely carry on top. The certificate limits the box itself to 65 lb gross. Put your own size into the calculator for your number.

    What is the difference between 32 ECT and 44 ECT?

    44 ECT board is about 38% stronger in stacking (44 ÷ 32), and its certificate allows 95 lb gross instead of 65 lb. Choose 44 ECT when boxes are heavier, stacked higher or stored in humid conditions.

    Is 32 ECT the same as 200# test?

    They are treated as equivalents for carrier rules (both allow 65 lb gross), but they measure different things. 32 ECT rates stacking strength; 200# rates burst strength. An ECT board usually stacks as well with less fiber, while a Mullen board resists punctures better.

    How do you calculate box compression strength from ECT?

    With the McKee formula: BCT = 5.87 × ECT × √(board thickness × box perimeter), using inches and lb/in. For a 12 × 10 in box (perimeter 44 in) in 1/8 in B-flute at 32 ECT: 5.87 × 32 × √(0.125 × 44) ≈ 440 lb.

    Why is the safe load so much lower than the BCT?

    BCT is measured in a lab, in a few minutes, at 50% humidity. In a warehouse the load sits for days or months, the air can be damp and stacks are rarely perfect. Those losses multiply, so a safety factor of 1.7 to 5 is normal. The calculator shows each loss so you can see where the strength goes.

    Does humidity really affect box strength?

    Yes, a lot. Corrugated board absorbs moisture from the air. Compared with 50% relative humidity, a box loses about 20% of its strength at 70% RH and about half at 90% RH, which is typical of cold stores.

    What ECT do I need for shipping with UPS or FedEx?

    Parcel carriers do not set one ECT, but they expect a box that matches its contents. As a rule of thumb, 32 ECT single wall suits most parcels up to about 65 lb; heavier or high-value items move to 44 ECT or double wall. Check the certificate limits in the chart above.

    What ECT are mailer boxes?

    Most printed mailer boxes are E-flute at 32 ECT, which is ideal for parcels that travel on their own. For heavier contents they can be made in B-flute or a higher grade.

    How do I convert ECT to kN/m?

    Multiply lb/in by 0.175. So 32 ECT ≈ 5.6 kN/m, 44 ECT ≈ 7.7 kN/m and 48 ECT ≈ 8.4 kN/m. Switch the calculator to cm · kg to see both.

    Can you make boxes to a specific ECT rating?

    Yes. Tell us the ECT you need — or the weight and stack height, and we will specify the board. Use “Get a quote for these boxes” and the size, board and conditions go straight into your request.

    Your Cart

    Your cart is empty

    Add a product to buy now, or request a custom quote. Browse Products